Secret Builders Society
02 / Build & Learn

Essential Tools for Your First Gunpla Build

Nippers, a hobby knife, sanding sticks, tweezers and a panel liner — what each does and how to use it safely.

Beginner · 7 min read

The short list

Gunpla snaps together without glue, so you do not need a large tool kit. For a first build, these five things cover almost everything:

  1. A pair of hobby nippers (side cutters)
  2. A hobby knife with spare blades, plus a cutting mat
  3. Sanding sticks or files in a few grits
  4. Fine tweezers
  5. A fine-tip panel lining marker (optional, but satisfying)

Add more only when you find a job these cannot do.

Nippers

Nippers cut parts away from the plastic frame, called the runner (or sprue). They are the one tool worth buying before anything else — scissors, nail clippers and twisting parts off by hand tend to leave white stress marks and gouges.

  • Use a two-step cut. First cut a little away from the part, leaving a small stub. Then make a second, careful cut flush with the part. This avoids stress marks.
  • Keep the flat side toward the part on the second cut for the cleanest surface.
  • Plastic only. Cutting wire or metal will damage fine hobby blades. Single-blade “ultimate” style nippers are especially delicate.

Hobby knife and safety

A sharp hobby knife shaves away the small leftover bump — the nub — after cutting. Used gently, it gives a smooth finish quickly. It is also the tool most likely to cause an injury, so build good habits from the start:

  • Always cut or scrape away from your body and away from the hand holding the part.
  • Work on a cutting mat, not on your lap or a table you care about.
  • Use light scraping strokes; let the blade do the work rather than pushing hard.
  • Replace dull blades — a dull blade slips. Dispose of old blades in a closed container.
  • Cap or retract the blade whenever you put the knife down.
  • Keep knives and small parts out of reach of young children and pets.

Sanding sticks

Sanding smooths any nub marks the knife leaves. Sanding sticks or sponge-backed pads are easier to control than loose paper. Grit numbers describe coarseness: lower is rougher.

  • Start around 400 to level the nub.
  • Move to 600–800 to remove scratches from the first pass.
  • Finish with 1000 or finer for a smooth surface.

Sanding can leave a slightly dull patch on coloured plastic. Many builders accept this, or even it out later with a matte topcoat. Sand only where you need to, and keep sharp edges crisp.

Tweezers

Fine tweezers make stickers, water-slide decals and tiny parts much easier to handle. Pointed tips are good for placing stickers; angled tips help with small parts. Lift stickers by one edge, align them, then press down with a cotton bud or the back of the tweezers.

Panel lining basics

Panel lining adds dark lines to the engraved recesses on armour, making detail stand out. It is the easiest upgrade for a first kit.

Markers — the easy start

Fine-tip or brush-tip panel lining markers let you trace the lines directly. Wipe away any mistakes with a cotton bud or a plastic-safe eraser before they dry.

Washes — the next step

Thin washes flow into recesses on their own. Some are enamel-based, and enamel thinner can make certain plastics brittle, especially on joints and parts under tension. Test on a spare runner first, use small amounts, avoid moving joints, and work with good ventilation. Always read the product’s own safety instructions.

Colour tip: dark grey usually looks more natural than pure black on white or light parts.

Your workspace

  • Good light — a desk lamp makes small parts far easier to see.
  • A small tray or container so parts do not roll away.
  • A bag for runner scraps, so you can clean up quickly.

Next, put these tools to work with How to Build Your First Gundam Model Kit, or check which grade suits you in Gunpla Grades Explained. You can also browse the hobby supplies listed in our catalogue.